The PSR has built in 20 MOA and offers the same great Features as our
LT111
The LT112 QD Scope Mount is designed for users that have a monolithic upper and
need 20 MOA to save them some elevation. The height is set for 1.535”.
The LT112s ring spacing of 2.9” allows the mounting of the US Optics T-PAL
scopes.
The LT112 comes complete with spare mounting screws with wrench, QD
adjustment wrench and instructions.
Available in 30mm or 34mm ring configurations.
About VFZ™ Mounts:
VFZ™ is a new theory in the concept of clamping accessories to MIL-STD-1913
rails. Instead of using a horizontal cross-bolt, the VFZ™ uses a vertical bolt
that draws up a clamping foot against the lower angle of the rail, seating the
mount similarly to a fully-closed LaRue lever. Once installed on the firearm,
index marks allow the user to remove the mount, then reattach to the same
tension, providing unprecedented return to zero for a non-QD-levered mount. The
unique vertical alignment of the clamp allows components that are structurally
stronger than traditional cross-bolt designs.
Why should I select VFZ™ Mounts instead of a QD Lever Mount?:
If you intend to leave an optic or accessory on a rail for the life of the
rifle, the VFZ™ option is for you. The VFZ™ is intended as a longer-term,
semi-permanent mounting alternative to our well-known Speed Levers. While both
mounts will allow the user to remove the mount from the weapon, reinstall it in
the same position, and return to zero, the VFZ™ mount is intended for users that
will not need to constantly remove and install their mounts (especially in the
field).
this is a great mount especially if you want more long range capabilities with 20 moa built in its great for shooting really far. i think larue has probably the highest quality mounts ON THE F'N PLANET!!
This mount sits proudly atop my humble remington r-25 in .308, but regularly gets removed and placed on guns that we are doing load development on beceause it is 100% reliable. When it goes back on the r-25 it is dead on, unless I put it on the wrong rail notch, but as it turns out that is user error.LOL :) Thank u LaRue u make a fine mount, and you're customer support was dead on reccomending this model to me.
I use this on my GA Precision .260 Rem AR, and it is a great mount, with 20 MOA built-in. Boringly reliable, repeatable, simple, effective.
I've owned a lot of LT-104's, LT-158's, but I like this one the best, since the AR10 has more rail space on the upper, you don't need an extended length mount.
The LT112 QD Scope Mount is designed for users that have a monolithic upper and need 20 MOA to save them some elevation. The height is set for 1.535”.
The LT112s ring spacing of 2.9” allows the mounting of the US Optics T-PAL scopes.
The LT112 comes complete with spare mounting screws with wrench, QD adjustment wrench and instructions.
Available in 30mm or 34mm ring configurations.
About VFZ™ Mounts:
VFZ™ is a new theory in the concept of clamping accessories to MIL-STD-1913 rails. Instead of using a horizontal cross-bolt, the VFZ™ uses a vertical bolt that draws up a clamping foot against the lower angle of the rail, seating the mount similarly to a fully-closed LaRue lever. Once installed on the firearm, index marks allow the user to remove the mount, then reattach to the same tension, providing unprecedented return to zero for a non-QD-levered mount. The unique vertical alignment of the clamp allows components that are structurally stronger than traditional cross-bolt designs.
Why should I select VFZ™ Mounts instead of a QD Lever Mount?:
If you intend to leave an optic or accessory on a rail for the life of the rifle, the VFZ™ option is for you. The VFZ™ is intended as a longer-term, semi-permanent mounting alternative to our well-known Speed Levers. While both mounts will allow the user to remove the mount from the weapon, reinstall it in the same position, and return to zero, the VFZ™ mount is intended for users that will not need to constantly remove and install their mounts (especially in the field).
Post new Review