LaRue Tactical 12.0" Handguard LT15-12

Need Help? Call 512-259-1585

Checkout Cart

LaRue Tactical 12.0" Handguard LT15-12

Your rating: None Average: 5 (1 vote)

| Reviews

$299.00

SKU: LT15-12

LaRue Tactical 12.0" Handguard LT15-12
12.0 inch free-floating handguard with LaRue Locking System.

Perfect balance with 16"-18" barrels, this rail covers mid-length gas blocks and provide true free-float. Our two-pin proprietary barrel nut system with its locking anti-slip plate, sets LaRue handguards apart from the competition. Once properly installed, there is no chance of movement whatsoever. The side and bottom rails are tucked closer to the barrel, keeping the profile narrower and more streamlined. LaRue handguards also include integral QD sling-swivel sockets at the base of each side for convenient mounting 2-point slings. Additionally, our Free-float Rail system provides an excellent heat-sinking feature that pulls throat-damaging heat away from the chamber area. Another heat-sinking benefit is the elimination of pressure-spikes, which some feel is the cause of a large part of pre-mature bolt failures.

Comes complete with Allen wrench, vial of blue Locktite and Instructions.

Weighs 1.05lb

CNC-machined out of aluminum

Integral QD sling-swivel sockets on both sides

Hard coat anodized, with T-Numbers

Low-profile bottom and side rails

Special rail cuts allow both mil-issue and standard rail covers

Re: LaRue Tactical 12.0" Handguard LT15-12

Thu, 2012-02-09 19:44 — sako204

Your Rating:

I installed this handguard on my Rock River Coyote Carbine in order to acquire more real estate for accessories and to increase the sight radius. My carbine came with a 7" handguard. I couldn't be happier with this product. It is top-notch and expertly finished. It is obviously constructed by very professional machinists.

Re: LaRue Tactical 12.0" Handguard LT15-12

Thu, 2011-08-11 20:48 — Anonymous

Your Rating:

Light, strong, won't cant when putting torque on a FUG. This is the only rail I'll own.

Post new Review

HANDGUARD ASSEMBLY INSTRUCTION

WARNING! MAKE SURE YOUR FIREARM IS UNLOADED COMPLETELY WITH NO ROUNDS IN THE CHAMBER AND NO MAGAZINE INSERTED. THE WEAPON SHOULD BE SAFE AT ALLTIMES.

Installation of the LaRue® free-float rail system

Please Supply these instructions to your professional Gunsmith

Handguard Rail	Handguard Nut	Barrel Nut	Spacer
Keeper(anti-rotation device)	8-32 x .80 SHCS 2ea.	Vial of Blue LocTite®	Uncle Mike’s® Sling compatible Swivel insert

Tool Requirements
· Armorer’s wrench · Action Block · Punch Set · Moly Grease · 9/64 L Hex wrench · Strap Wrench

1. Remove the upper from the rifle. Remove the Handguard. Remove the muzzle device. Remove the front sight base. Unscrew and remove the factory barrel nut and delta ring assembly (you won’t need these)

Note: On certain Action Blocks, it May be necessary to Dremel® out an area to accommodate the “Keeper” during installation

2. Next, Place the “Keeper” on the upper receiver, slip on the “Handguard Nut”, then the “Barrel Nut”

3. Add a small amount of Moly Grease to the receiver threads. The “Barrel Nut” is installed just like any other; you snug it up three times, then torque it until the next gas tube hole aligns correctly

4. Install the Spacer.

5. Slip on the float tube and tighten the “Handguard nut”. The tube will align itself with locating pins already in the float tube. Use a strap wrench to get the Handguard Nut” tight.

Uppers

Lowers

Rifle Scope

Red Dot

Night Vision

Scope Mounts

Light/Laser Mounts

Accessory Mounts

LaRue Tactical 12.0" Handguard LT15-12

Post new Review

LaRue Tactical 7.0" Handguard LT15-...

LaRue Tactical 9.0" Handguard LT15-...

LaRue Tactical 11" Handguard FULL L...